(
(
How to
How to
)
)
Changing straps on the Vanitas
Changing straps on the Vanitas
It isn't that hard, after the first try
It isn't that hard, after the first try
by
Arena
3
min read
Built for Adaptability
The Vanitas was engineered with both durability and versatility in mind. While its design philosophy is rooted in purpose and restraint, it also respects the individuality of its wearer. Adjusting or changing the bracelet isn’t about customization for fashion, it’s about achieving the right balance between fit, function, and comfort. The bracelet’s link system and solid end connections are built to handle years of wear and adjustment without failure.
Understanding the System
The Vanitas bracelet uses solid stainless steel links connected by screw secured pins, a design chosen for its strength and serviceability. Cheap or press fit link systems tend to loosen, shear, or seize over time. Screw systems, by contrast, can be precisely adjusted with the proper tools and maintained for decades. When resizing:
Use a precision screwdriver designed for fine watch hardware, avoid multi-bit or oversized tools.
Work on a soft surface to prevent scratching.
Use one flathead screwdriver to hold the pin and another flathead screwdriver to loosen the screw.
Remove or add links evenly from both sides of the clasp to maintain symmetry and balance.
Tighten each screw firmly but without over torquing; a touch of low strength thread locker can secure the screws if needed.
Changing the Bracelet
The Vanitas features a drilled through lugs, adapted for both fabric and metal attachments. When switching from bracelet to strap, use the drilled-through lug holes for controlled removal of spring bars. Press a pushpin tool (or paperclip, or safety pin, or your girlfriends earring) into the drilled holes to remove spring bars. Once the bracelet is detached, inspect all connection points and clean away debris or moisture before reassembly. Always give it a tug to ensure spring bars are secure.
Why It Matters
Every change, no matter how small, interacts with the mechanical integrity of the watch. A poorly fitted bracelet or a stripped screw can compromise comfort, stability, or even the case itself. Proper tools, patience, and precision ensure that the Vanitas remains as strong as the day it left the workshop. Adjusting your bracelet isn’t just maintenance, it’s part of the discipline of ownership. A watch like this rewards care, and every small adjustment is a reminder of what separates true engineering from convenience.
Built for Adaptability
The Vanitas was engineered with both durability and versatility in mind. While its design philosophy is rooted in purpose and restraint, it also respects the individuality of its wearer. Adjusting or changing the bracelet isn’t about customization for fashion, it’s about achieving the right balance between fit, function, and comfort. The bracelet’s link system and solid end connections are built to handle years of wear and adjustment without failure.
Understanding the System
The Vanitas bracelet uses solid stainless steel links connected by screw secured pins, a design chosen for its strength and serviceability. Cheap or press fit link systems tend to loosen, shear, or seize over time. Screw systems, by contrast, can be precisely adjusted with the proper tools and maintained for decades. When resizing:
Use a precision screwdriver designed for fine watch hardware, avoid multi-bit or oversized tools.
Work on a soft surface to prevent scratching.
Use one flathead screwdriver to hold the pin and another flathead screwdriver to loosen the screw.
Remove or add links evenly from both sides of the clasp to maintain symmetry and balance.
Tighten each screw firmly but without over torquing; a touch of low strength thread locker can secure the screws if needed.
Changing the Bracelet
The Vanitas features a drilled through lugs, adapted for both fabric and metal attachments. When switching from bracelet to strap, use the drilled-through lug holes for controlled removal of spring bars. Press a pushpin tool (or paperclip, or safety pin, or your girlfriends earring) into the drilled holes to remove spring bars. Once the bracelet is detached, inspect all connection points and clean away debris or moisture before reassembly. Always give it a tug to ensure spring bars are secure.
Why It Matters
Every change, no matter how small, interacts with the mechanical integrity of the watch. A poorly fitted bracelet or a stripped screw can compromise comfort, stability, or even the case itself. Proper tools, patience, and precision ensure that the Vanitas remains as strong as the day it left the workshop. Adjusting your bracelet isn’t just maintenance, it’s part of the discipline of ownership. A watch like this rewards care, and every small adjustment is a reminder of what separates true engineering from convenience.
